Linx-technologies LICAL-TRC-MT Manual de usuario descargar pdf (Pagina 13)

– – – –

20 21

Serial Interface Command Set Denitions

There are ten functions using the Serial Interface Engine (SIE). Each

function has the ability to read the current setting from the MT or write new

information to the speciﬁed conﬁguration setting.

Serial Interface Command Set Deﬁnitions

Command Description

Local Settings

Reads and writes the device’s local 24-bit address and

status line conﬁguration. This allows the option to program all

devices with the same address and status line conﬁguration,

or increment the address to utilize the full range of addresses.

Next User ID

Reads and writes the next available ID location, which will be

given to the next user manually learned into the system.

Speciﬁc User

Reads and writes the 24-bit address and status line

conﬁguration for a speciﬁc user learned into the system. If a

device in the system is lost or stolen, that speciﬁc device can

be removed from the system and replaced with a new one

without having to erase the memory and re-learn all of the

other devices in the system. To remove an existing user, write

0xFF into the address and status line values. 0xFF should not

be used as a learned user.

Target Address

Reads and writes the local device’s 24-bit target address. This

allows a user to communicate directly with a speciﬁed target

device and not with any other devices even though they may

have been authorized for communication.

Custom Data Value

Reads and writes a single byte that is sent when Custom Data

is enabled. If enabled, the byte is sent with each packet, and

then output on the SER_IO line of the receiving device along

with the TX ID value and the status line value.

Latch Mask

Reads and writes the Latch Mask for the status line

outputs. This allows each status line to be individually set as

momentary or latched.

Status Value

Reads the current state of the transcoder’s status line outputs.

Writes the value of the status line inputs to send (subject to

I/O mask) and the number of packets to send.

Conﬁrmation EN

Reads and writes the device’s conﬁrmation enable setting.

When enabled, the receiving transcoder immediately transmits

a conﬁrmation packet back to the originating transcoder.

The originating transcoder validates the conﬁrmation and

then activates its CONFIRM line. If the conﬁrmation is not

necessary or the user wants to free the air of additional

transmissions, conﬁrmation can be disabled and the receiving

device does not transmit a conﬁrmation packet.

Targeting EN

Reads and writes the device’s target enable setting. This

enables or disables the option for the transcoder to send a

targeted data packet.

Custom Data EN

Reads and writes the transcoder’s custom data setting. This

enables or disables the option for the transcoder to send a

custom data byte with each transmission.

Figure 16: Serial Interface Command Set Deﬁnitions

MT Series Transcoder Serial Interface Engine Timings (ms) at 28,800bps

SER_IO = Input SR_IO = Output

Deﬁnition Min

Ready

Max

Ready

Receive

Cmd

Process

Cmd

Wait

Transmit

Finish

Process

Min Total

Time

Max Total

Time

Read Local Settings 0.08 17.00 2.80 1.11 4.00 3.10 0.04 11.13 28.05

Write Local Settings 0.08 17.00 2.80 1.03 4.00 1.73 17.80 27.44 44.36

Read Next User ID 0.08 17.00 2.80 1.06 4.00 2.07 0.04 10.06 26.97

Write Next User ID 0.08 17.00 2.80 1.04 4.00 1.73 3.65 13.30 30.22

Read Speciﬁc User 0.08 17.00 2.80 1.11 4.00 3.11 0.04 11.14 28.06

Write Speciﬁc User 0.08 17.00 2.80 1.04 4.00 1.73 14.30 23.95 40.87

Read Target Address 0.08 17.00 2.80 1.10 4.00 2.77 0.04 10.79 27.71

Write Target Address 0.08 17.00 2.80 1.05 4.00 1.73 10.74 20.40 37.32

Read Custom Data Value 0.08 17.00 2.80 1.07 4.00 2.08 0.04 10.07 26.99

Write Custom Data Value 0.08 17.00 2.80 1.05 4.00 1.73 3.65 13.31 30.23

Read Latch Mask Value 0.08 17.00 2.80 1.07 4.00 2.08 0.04 10.07 26.99

Write Latch Mask Value 0.08 17.00 2.80 1.05 4.00 1.73 3.65 13.31 30.23

Read Status Outputs 0.08 17.00 2.80 1.05 4.00 2.08 0.04 10.05 26.97

Write Status Inputs 0.08 17.00 2.80 1.06 4.00 1.73 ** 9.73 26.65

Read Conﬁrmation EN 0.08 17.00 2.80 1.07 4.00 2.08 0.04 10.07 26.99

Write Conﬁrmation EN 0.08 17.00 2.80 1.06 4.00 1.73 3.65 13.32 30.24

Read Device Targeting EN 0.08 17.00 2.80 1.08 4.00 2.08 0.04 10.08 27.00

Write Device Targeting EN 0.08 17.00 2.80 1.06 4.00 1.73 3.65 13.32 30.24

Read Custom Data EN 0.08 17.00 2.80 1.08 4.00 2.08 0.04 10.08 27.00

Write Custom data EN 0.08 17.00 2.80 1.07 4.00 1.73 3.65 13.33 30.25

MinRdy applies when MT is in Encoder Only mode.

MaxRdy applies when MT is in Transcoder mode and time may be longer due to possible receive timeout period.

Receive Command is calculated for 8 bytes at 28,800bps (34µs/bit).

Transmit Reply is measured on the SER_IO pin from the MT

** Finish Process time for the Write Status Inputs command = 0.06ms + (Packet Time * Number of Packets). See Figure 19 for Packet Time.

Figure 15: MT Series Transcoder Serial Interface Engine Timings (ms) at 28,800bps

1 2 ... 8 9 10 11 12 13 14 15 16 17 18 19 20 21

Comentarios a estos manuales

Sin comentarios

Linx-technologies LICAL-TRC-MT Manual de usuario Pagina 13

Comentarios a estos manuales

Relacionado con productos y manuales para Hardware Linx-technologies LICAL-TRC-MT